Binding Installation Guide
Select Your Product:
Step On® Overview
How It Works
Step On® Sizing
Compatibility
Patent Information
Part Terminology
Toe Clips
Heel Clip
Release Lever
Getting In and Out
Step 1
Step 2
Step 3
Step 4
Step 5
Warning
Universal Steps
Disk Guide
Read More
Stance - Regular or Goofy
あなたのスタンスはレギュラーですか、それともグーフィーですか?まだわからない?では、確認してみましょう! 以下は、あなたのスタンスを判断するための簡単なテストです。:
- スケートを滑る時、左足と右足のどちらの足が前にありますか?
- 床を横向きに滑るとしたら、どちらの足が前に来ますか?
右足前=グーフィー
左足前=レギュラー
両方当てはまる? = スノーボードに行って、どちらがやりやすいか確認しましょう。
Read More
あなたのスタンスはレギュラーですか、それともグーフィーですか?まだわからない?では、確認してみましょう! 以下は、あなたのスタンスを判断するための簡単なテストです。:
- スケートを滑る時、左足と右足のどちらの足が前にありますか?
- 床を横向きに滑るとしたら、どちらの足が前に来ますか?
右足前=グーフィー
左足前=レギュラー
両方当てはまる? = スノーボードに行って、どちらがやりやすいか確認しましょう。
Read More
Size Chart
Read More
Stance - Width and Angles
スタンス幅: メジャーを使って測定するか、目で見ながら快適な位置を見つけてください。自分のライディング スタイルに最適なスタンスを見つけるには、経験が必要になる場合があります。スタンスの広さ/狭さがわからない場合は、肩幅より少し広くして、そこから変更してみてください。
アングル(角度): スタンス幅と同じように、バインディングの角度も個人の好みとライディングスタイルに左右されます。よくわからない場合は、色々な角度を試して、そこから修正してください。
スタンスは 5 分で設定できるものですが、完璧にするには 5 年かかる場合があることを忘れないでください。スタンスやアングルには、正解も不正解もありませんので、いろいろ試してみて、自分に合うものを見つけてください。
注意: バインディングをボードにセットアップするときは、ラチェットが外側に向いていることを確認し、左右逆向きに装着しないようお気を付けください。
Read More
スタンス幅: メジャーを使って測定するか、目で見ながら快適な位置を見つけてください。自分のライディング スタイルに最適なスタンスを見つけるには、経験が必要になる場合があります。スタンスの広さ/狭さがわからない場合は、肩幅より少し広くして、そこから変更してみてください。
アングル(角度): スタンス幅と同じように、バインディングの角度も個人の好みとライディングスタイルに左右されます。よくわからない場合は、色々な角度を試して、そこから修正してください。
スタンスは 5 分で設定できるものですが、完璧にするには 5 年かかる場合があることを忘れないでください。スタンスやアングルには、正解も不正解もありませんので、いろいろ試してみて、自分に合うものを見つけてください。
注意: バインディングをボードにセットアップするときは、ラチェットが外側に向いていることを確認し、左右逆向きに装着しないようお気を付けください。
Read More
Components and Tools
Components
Tools Needed
Binding Adjustments
Heelcup Adjustment
Disk Cover Adjustment
Toe Strap Adjustment - Toe Cap vs. Over The Top
Toe Strap Adjustment - Boot Length
Toe Strap Adjustment - Centering
Ankle Strap Adjustment - Centering
Highback Adjustment - Rotation
Highback Adjustment - Forward Lean
Binding Installation
Step 1: Mount Adapter Plates
Step 2: Mount Split Disk
Step 3: Mount Bindings
Step 4: Mount Touring Brackets
Touring Mode Instructions
Step 1: Touring Bracket
Step 2: Forward Lean
Step 3: Heel Riser
Step 4: Crampons
Ride Mode Instructions
Step 1: Push Down
Step 2: Rotate
Step 3: Lock
Step 3: Lock
Step 4: Forward Lean
Select Your Board Pattern
Mounting Your Bindings
- 1. Remove the disk cover screw.
- 2. Slide the disk cover out and place to the side.
- 3. Place the disk into the center of the binding at your desired stance angles.
- 4. Align the disk with the board's inserts that you plan on using.
- 5. If mounting to a 4x2 or 4x4 pattern, use the 4 large Power Washers and 8 screws.If mounting to the Channel use the 4 standard washers and 4 screws.
- 6. Using a #3 Phillips screwdriver, hand thread each screw with a washer into place.
- 7. Start with one full turn on each screw, then contin- ue tightening one full turn each while alternating screw to screw until all screws are equally tight.
- 8. Slide the disk cover to your desired setting and rethread the screw to secure.
Tech Tip
If you're having a hard time getting your screws to reach the inserts, begin by threading one screw with no washer. This will pull the binding closer to the top sheet and allow you to easily thread the remaining screws and washers. Once you have threaded the remaining screws, take out the first screw and reth- read with a washer.

BEGINNER
INTERMEDIATE
ADVANCED